|
|
|
|
|
|
YUKON FORD 8.8 C CLIP YGA-33083
|
|
|
SOLD EACH
C-CLIP FOR CHRYSLER 8.25, FORD 8.8 GM 12BOLT, GM 8.2 8.5 8.6
.150 THICK
Yukon Gear & Axle C-clips keep a hold on your axles. These little steel C-clips are mighty important, so they're precision-crafted to stay in the groove and prevent your shaft from sliding out. What's holding your axles on? Trust Yukon Gear & Axle C-clips to do the job.
|
|
|
|
|
|
|
|
|
|
YUKON FORD 8.8 CROSS PIN DIFFERENTIAL LOCK BOLT 33067
|
|
|
SOLD EACH
THIS IS WHAT YOU NEED FOR YOUR DAMAGED OR LOST FORD 8.8 CROSS PIN BOLT
FIT FORD 8.8 28 SPLINE
8.8 31 SPLINE
8.8 IRS 28 SPLINE
PASSENGER CAR
8.8 IRS SUV
|
|
|
|
|
|
|
|
|
|
8.8" FORD 7/8" CROSS SHAFT PIN
|
|
|
FORD 8.8 CROSS SHAFT 7/8
|
|
|
|
|
|
|
|
|
|
Lube Locker Ford 8.8" Differential Cover Gasket LLR-F880
|
|
|
Part Number: LULLLR-F880
Ford 8.8"
No additional sealant needed
Elastomer beading on both sides of gasket
No setup time
Will not fit IFS front or IRS rear
Throw your RTV away! Tired of the mess that silicone sealant leaves behind? Ever had to wail on the diff cover with a hammer to break it free? Lube Lockerâ„¢ gets the job done quicker with less hassle and mess. These gaskets are designed with a steel core that is rubber coated and have Lube Locker's signature full perimeter elastomer beading on BOTH sides. The result is a gasket that will not split or extrude during installation and has superior torque retention. There is no set up time because installation is dry with no sealant needed!
|
|
|
|
|
|
|
|
|
|
8.8" FORD MASTER INSTALL KIT EARLY 35-2013
|
|
|
Part Number: G/235-2013
For Use In 2008 And Earlier
Axles
Pinion Nut
Pinion Seal
Timken Outer Pinion Bearing And Race
Crush Sleeve
Timken Inner Pinion Bearing And Race
Pinion Shims
Carrier Shims
Carrier Bearings And Races
Ring Gear Bolts
Thread Locking Compound
Gear Marking Compound
Silicone Sealer
G2 Master kits include all the parts that are needed to properly install a ring and pinion. These G2 kits include hard to find parts like a proper shim kit, replacement pinion nut , crush sleeve, pinion seal, pinion bearings, carrier bearings, ring gear bolts, silicone sealer, locktite and gear marking compound.
|
|
|
|
|
|
|
|
|
|
8.8" FORD 31 SPLINE OPEN DIFF SPIDER GEAR KIT
|
|
|
FORD 8.8 OPEN DIFF SPIDER GEAR KIT WITH CROSS SHAFT
|
|
|
|
|
|
|
|
|
|
8.8" FORD 31 SPLINE TRAC LOCK SPIDER GEAR KIT
|
|
|
HAS YOUR NEWER FORD F150 WITH A FACTORY TRAC LOCK EATEN THE SPIDER GEARS AND YOU CAN FIND THEM.
WELL NOW YOU HAVE.
DOES NOT COME WITH CROSS SHAFT.
|
|
|
|
